Products > Medical Gas, Oxygen & Suction Unit
Humidifier Bottle

Humidifier Bottle

Humidifier-Bottle-001
  • 500 cc humidifier cylinder made of POLYSULPHON, durable, not broken if dropped
  • The cylinder can be sterilized by autoclaving
  • There is a check valve to release pressure when the pressure exceeds 2 PSI or 40 mm/Hg

PDF Download

Featured Products

See All
Vacuum-Trolley-For-Anesthetist-001

Vacuum Trolley For Anesthetist

Set for suctioning fluids and blood from patients for use in the operating room, 1 bottle type

  • Adjustable suction rate from 0 – 760 mm/Hg
  • There is a button to turn on/off the direct suction (DIRECT LINE)
  • There is an overflow bottle (TRAP BOTTLE) to prevent liquid from overflowing into the system. The bottle is made of durable polysulfone, does not break when dropped
  • One 3-liter sputum container with level markings
  • The cart has 5 wheels for easy movement and has one CONDUCTIVE WHELL wheel to prevent static electricity.
Ball-Valve-Model-SP150-001

Ball Valve with Extensions Model SP150

Cleaned for medical gas use and 100% hydrostatic tested, these 3 piece medical gas valves are designed to meet the NFPA 99c, ISO 7396-1 & G-01 standards.

Specifications

  • Valve shall be 3 piece ball-type full bore design, with a bronze/ brass body, stainless steel ball, stem, bolts & nuts.
  • Seat shall be Teflon (RPTFE) and seals Viton.
  • Valves ½” to 2” shall have a minimum pressure rating of 4137 kpa (600 psi) wog.Valves 3” to 4” shall have a minimum pressure rating of 2758 kpa (400 psi) wog.
  • Valve shall require only a quarter turn from fully open position to a fully closed position.
  • Extensions stubs shall be K type with a minimum 150 mm long to allow brazing without damaging the valve seat and seals due to heat transfer during brazing operati
  • Each valve shall be hydrostatically tested for leakages.
  • Each valve shall be washed and degreased for medical gas use.
  • Pipe stubs extensions shall be capped at both ends.
  • The valves shall be supplied in sealed plastic bags, marked with “Oxygen” or “cleaned for oxygen use”, to prevent contamination prior to installation.
  • Valves shall be Silbermann model SP150 or equivalent.
  • All valves shall comply with NFPA 99, ISO 7396-1 & G-01 standards.

Medical Gas System Standards:

  • NFPA99, EN ISO 7396-1 & G-01 requirements.

Silbermann’s Quality Management System:

  • EN ISO 13485-2016
    ISO 9001-2015. Medical Gas System Standards:
Nebulizer-Bottle-001

Nebulizer Bottle

Oxygen percentage adjustable spray bottle

  • Oxygen spray cylinder, adjustable to 3 levels, 40%, 70% and 100%
  • 500 cc spray cylinder made of POLYSULPHON, durable, not broken when dropped. The cylinder can be sterilized by autoclaving.
  • The mist generator can be removed for cleaning in case of clogging.
  • There is a hole for a HEATER for heating.
  • There is a hole for a check valve to release pressure if the pressure exceeds 2 PSI or 40 mm/Hg.
Oxygen-Flowmeter-Wall-Mounted-001

Oxygen Flowmeter Wall Mounted

Oxygen flowmeter 0- 15 liters/minute, wall mounted

  • Flowmeter can adjust oxygen flow rate from 0 – 15 liters/minute
  • Made of anodized aluminum, light weight
  • There is a dust filter inside the flowmeter.
MARKUS-mainDoor-004

Secondary entrance door SCRUB ROOM (MANUAL type)

It is a single opening door (SINGLE HINGED DOOR) of the SEMI AIR TIGHT type with a glass window. The door size is approximately 0.90 x 2.00 meters. The top and sides of the door edge have RUBBER SEALING PROFILE rubber sheets installed and the bottom edge of the door has a DROP SEAL rubber edge installed. DROP SEAL type with equipment. The door is a hinged door that automatically closes the door, and the door handle with key is the DEAD LOCK type. Material standards – ISO 9001:2000 standard.

Ceiling-Mounted-Flexible-Hose-001

Ceiling Mounted Flexible Hose

Ceiling Mounted Flexible Hoses are used for delivering gas through a retractable hose in large rooms like OT’s.

On one end, this hose assembly is connected to the ceiling gas outlet with a DISS/Nist fitting that is suitable for the required gas type. On the other end, it is connected to a portable gas outlet that has the same gas coding as the ceiling outlet.

A pulley (key back) is attached to the hose to easily adjust its height according to the user’s needs.

Features

  • A quick connect outlet with flexibility in use – you can pull the hose down with its connecting adapter and then release it, to move back to its original place.
  • Cost-effective – alternative for using pendants in OTs.
  • Fits for rooms where it is difficult to install outlets in the side walls.

Technical Data

  • Hose length:
    • maximum extension – 1.65 m
    • retractable position – 1.20 m
  • Available for all medical gases: Oxygen, Vacuum, Medical Air, Nitrous-Oxide N2 and Co2.
  • Portable gas outlets that can be attached to the hose are available in several standards including DIN, ENV, Sil-Ohio, Puritan Bennett, Chemetron, and British standard*.
  • Retractable hoses work with a pulley (key back).
  • Each medical gas outlet and hose has a gas coding to avoid inappropriate gas usage.

Medical Gas System Standards:

  • NFPA 99, EN ISO 7396-1 & GO-1, HTM 02-01 requirements

Applicable Standards:

  • NFPA 99, ISO 9170-1, ISO 5359

Silbermann’s Quality Management System:

  • EN ISO 13485-2016, ISO 9001-2015

* Other types of portable outlets are available by customers’ request

Contact Us

J.E.P. enterprise,co.ltd

  • 235/8 21 สุขุมวิท 21 (อโศก) แขวงคลองเตยเหนือ เขตวัฒนา กรุงเทพมหานคร 10110
  • 02 258 0447
  • info@jep.co.th

Useful Links

Follow Us

Facebook Line

© Copyright J.E.P. enterprise,co.ltd 2024.