Products > Operating Theatre, Surgical Light
Power LED Surgical Light

Power LED Surgical Light

POWER-LED-001
  • Illumination 100,000 lux – 110,000 lux
  • Color Temperature  3,800 K
  • LED Bulb  /  Ambient  Light
  • Lamp Life  40,000  hrs.
  • Complies with  Laminar Flow System
  • With AIM (Automatic Illumination Management) System

PDF Download

Featured Products

See All
Suction-Unit-Wall-Mounted-001

Suction Unit Wall Mounted

Wall-mounted sputum suction unit for patients

  • Adjustable suction rate 0 – 760 mm/Hg or 0 – 200 mm/Hg
  • With overflow bottle (TRAP BOTTLE) to prevent liquid from overflowing into the system. The bottle is made of durable polysulfone, does not break when dropped
  • The bottle holds 1,800 cc of liquid and sputum. The bottle is clear and can be seen all around. There are lines indicating the amount of liquid. Can be sterilized by steam, convenient for cleaning, with a hanging basket.
Bubble-Jet-Bottle-001

Bubble Jet Bottle

Humidifier and mist bottle

  • Humidifier and spray bottle (Bubble Jet) size 500 cc.
  • Made of polysulfone (POLYSULPHON), durable, not broken when dropped. The atomizer can be removed for cleaning in case of clogging.
  • The bottle can be sterilized by autoclaving.
  • There is a check valve slot to release pressure when the pressure exceeds 2 PSI or 40 mm/Hg.
Ball-Valve-Model-SP150-001

Ball Valve with Extensions Model SP150

Cleaned for medical gas use and 100% hydrostatic tested, these 3 piece medical gas valves are designed to meet the NFPA 99c, ISO 7396-1 & G-01 standards.

Specifications

  • Valve shall be 3 piece ball-type full bore design, with a bronze/ brass body, stainless steel ball, stem, bolts & nuts.
  • Seat shall be Teflon (RPTFE) and seals Viton.
  • Valves ½” to 2” shall have a minimum pressure rating of 4137 kpa (600 psi) wog.Valves 3” to 4” shall have a minimum pressure rating of 2758 kpa (400 psi) wog.
  • Valve shall require only a quarter turn from fully open position to a fully closed position.
  • Extensions stubs shall be K type with a minimum 150 mm long to allow brazing without damaging the valve seat and seals due to heat transfer during brazing operati
  • Each valve shall be hydrostatically tested for leakages.
  • Each valve shall be washed and degreased for medical gas use.
  • Pipe stubs extensions shall be capped at both ends.
  • The valves shall be supplied in sealed plastic bags, marked with “Oxygen” or “cleaned for oxygen use”, to prevent contamination prior to installation.
  • Valves shall be Silbermann model SP150 or equivalent.
  • All valves shall comply with NFPA 99, ISO 7396-1 & G-01 standards.

Medical Gas System Standards:

  • NFPA99, EN ISO 7396-1 & G-01 requirements.

Silbermann’s Quality Management System:

  • EN ISO 13485-2016
    ISO 9001-2015. Medical Gas System Standards:
MARKUS-mainDoor-004

Secondary entrance door SCRUB ROOM (MANUAL type)

It is a single opening door (SINGLE HINGED DOOR) of the SEMI AIR TIGHT type with a glass window. The door size is approximately 0.90 x 2.00 meters. The top and sides of the door edge have RUBBER SEALING PROFILE rubber sheets installed and the bottom edge of the door has a DROP SEAL rubber edge installed. DROP SEAL type with equipment. The door is a hinged door that automatically closes the door, and the door handle with key is the DEAD LOCK type. Material standards – ISO 9001:2000 standard.

Anaesthetics-Gas-001

Anaesthetics Gas Scavenging Service Inlet (Venturi type)

The Silbermann jet scavenging inlet is designed for safe removal of surplus anaesthetic gas from the operating theatre.

The scavenging inlet assembly uses compressed air to create suction and propels the contaminated air to the outside atmosphere.

Features

  • Operation based on compressed air – No need for a central AGSS system
  • When probe is connected, green pneumatic indicator showing system is in use
  • Very quiet operation
  • Automatic shut off when probe is disconnected
  • Flow and vacuum adjustment
  • Locking mechanism quick connect

Medical Gas System Standards:

  • NFPA99
  • ISO 7396
  • G-01
  • HTM 02-01

Silbermann’s Quality Management System:

  • EN ISO 13485-2016
  • ISO 9001-2015
  • CE marked
Oxygen-Therapy-Unit-with-Humidifier-001

Oxygen Therapy Unit with Humidifier Rail Mounted

Oxygen and humidifier set hanging on equipment rail

  • Flowmeter, adjust oxygen flow rate 0 – 15 liters/minute
  • The housing is made of anodized aluminum, light weight
  • There is a dust filter inside the flowmeter
  • 500 cc humidifier cylinder made of polysulfon (POLYSULPHON), durable, not broken, made free from germs by autoclaving
  • There is a check valve slot to release pressure when the pressure exceeds 2 PSI or 40 mm/Hg
  • There is a holder on the equipment hanger to move back and forth to the desired position

Contact Us

J.E.P. enterprise,co.ltd

  • 235/8 21 สุขุมวิท 21 (อโศก) แขวงคลองเตยเหนือ เขตวัฒนา กรุงเทพมหานคร 10110
  • 02 258 0447
  • info@jep.co.th

Useful Links

Follow Us

Facebook Line

© Copyright J.E.P. enterprise,co.ltd 2024.